Tuesday, April 7, 2015

Leave a Comment

RIP Configuration in IPv6 {CCNP Part2}

RIPng Configuration
Ø  R1(config)#ipv6 unicast-routing         {enable IPv6 on Router}
Ø  R1 (config)#ipv6 cef                                {enable cisco express forwarding (CEF) for IPv6.
CEF is a highly-efficient packet switching technology supported by Cisco router.}

v  Router1 interfaces Configuration
Ø  R1(config)#interface serial 2/0
Ø  R1(config-if)#description CONNECTED WITH R2
Ø  R1(config-if)#ipv6 address 2001:1::1/64
Ø  R1(config-if)#clock rate 64000
Ø  R1(config-if)#no shut
Ø  R1(config-if)#exit

Ø  R1(config)#interface fastEthernet 0/0
Ø  R1(config-if)#description CONNECTED WITH SW1
Ø  R1(config-if)#ipv6 address 2001:4::1/64              
Ø  R1(config-if)#no shut
Ø  R1(config-if)#exit

v  Router2 Enable IPv6
Ø  R2(config)#ipv6 unicast-routing
Ø  R2(config)#ipv6 cef

v  Router2 interfaces Configuration
Ø  R2(config)#interface serial 2/0
Ø  R2(config-if)#description CONNECTED WITH R1
Ø  R2(config-if)#ipv6 address 2001:1::2/64
Ø  R2(config-if)#no shut
Ø  R2(config-if)#exit

Ø  R2(config)#interface serial 2/1
Ø  R2(config-if)#description CONNECTED WITH R3
Ø  R2(config-if)#ipv6 address 2001:2::1/64
Ø  R2(config-if)#clock rate 64000
Ø  R2(config-if)#no shut
Ø  R2(config-if)#exit

v  Router3 Enable IPv6
Ø  R3(config)#ipv6 unicast-routing
Ø  R3(config)#ipv6 cef


v  Router2 interfaces Configuration
Ø  R3(config)#interface serial 2/1
Ø  R3(config-if)#description CONNECTED WITH R2
Ø  R3(config-if)#ipv6 address 2001:2::2/64
Ø  R3(config-if)#no shut
Ø  R3(config-if)#exit

Ø  R3(config)#interface fastEthernet 0/0
Ø  R3(config-if)#description CONNECTED WITH SW2
Ø  R3(config-if)#ipv6 address 2001:3::1/64
Ø  R3(config-if)#no shut
Ø  R3(config-if)#exit

v  RIPng Protocol Configuration in R1 under the interface:-
Ø  R1(config)#interface serial 2/0
Ø  R1(config-if)#ipv6 rip DEMO-RIP enable   {DEMO-RIP:- name to identify the RIP Process}
Ø  R1(config-if)#exit

Ø  R1(config)#interface fastEthernet 0/0
Ø  R1(config-if)#ipv6 rip DEMO-RIP enable
Ø  R1(config-if)#exit

v  RIPng Protocol Configuration in R2 :-
Ø  R2(config)#interface serial2/0
Ø  R2(config-if)#ipv6 rip DEMO-RIP enable
Ø  R2(config-if)#exit

Ø  R2(config)#interface serial 2/1
Ø  R2(config-if)#ipv6 rip DEMO-RIP enable
Ø  R2(config-if)#exit

v  RIPng Protocol Configuration in R3 :-
Ø  R3(config)#interface serial 2/1
Ø  R3(config-if)#ipv6 rip DEMO-RIP enable
Ø  R3(config-if)#exit

Ø  R3(config)#interface fastEthernet 0/0
Ø  R3(config-if)#ipv6 rip DEMO-RIP enable
Ø  R3(config-if)#exit

{Configuration is done}

v  Troubleshooting & Verification Commands
Ø  Show ipv6 route
Ø  Show ipv6 interface brief
Ø  Show ipv6 protocols
Ø  Show ipv6 rip {option}

Ø  Debug ipv6 rip {option}

0 comments:

Post a Comment